![how to wire an adafruit trinket how to wire an adafruit trinket](https://cdn-learn.adafruit.com/assets/assets/000/019/197/medium800/light_daft-circuit.jpg)
I've gone through the instructions repeatedly and tried it on my MacBook Air (Yosemite) since the driver step shouldn't be necessary on a mac, but I had the same result - no active com port selection. I've tried several different Trinkets with the same results. The Trinket doesn't show in the Device Manager. I'm not sure if both of those last two steps are necessary - I would think it would be one or the other.Īfter installing all this, I never get the option to add my own driver which is supposed to happen in Windows. That didn't work so I downloaded the Fake USB and followed those instructions (I installed and setup the com0com tool). I added the board to my list (by adding the URL in Preferences). Arduino Trinket but the com port selector under 'Tools' remains grayed out.
#How to wire an adafruit trinket code
Tip: For key combinations, each key must be "pressed" by the Arduino code in sequence using a Keyboard.press() command for each key as shown on the example code.I have spent hours trying to upload a sketch to a 5v. See the Arduino documentation for more information on the key modifiers. The first one toggles the mute button on Skype while the second one locks the screen on Windows. The program is set up to provide two keyboard shortcuts in response to a button-press: Windows-F4 and Windows-L. Once the environment is installed, start a new project, copy the code at the end of this page, select the board type, the port and upload the program. Tip: If you plan on using a non-Arduino-branded board (like the Adafruit Trinket M0 in this project), it is easier to follow the manufacturer's instructions, for example t he Adafruit Arduino IDE setup page, as they include setting up the environment with the corresponding boards and libraries.
![how to wire an adafruit trinket how to wire an adafruit trinket](https://cdn-blog.adafruit.com/uploads/2020/10/show-and-tell-10-14-2020-showand.jpg)
If you don't already have an Arduino environment installed, this is the time to do it. Depending on the buttons used, this can mean that either the buttons have to be tested unsoldered, or they have to be desoldered and resoldered after installation inside the case. Tip: Always test the code and wiring before starting to put the electronics inside the enclosure. If you use buttons as shown in this project that are screwed from the bottom, make sure you solder the buttons after they are in place in their respective holes. That makes it easier to attach the wires to the legs and greatly simplifies soldering. Most buttons have small holes in their legs. I suggest soldering the wires to the Trinket from the top (as shown on the picture below) so that there is no clearance issue at the bottom. The connections are shown on the fritzing diagram at the bottom of this page. There are just 7 solder joints to make on this project. Tip: I recommend using solid core wires for this project as they are easier to solder and work with and they will not be exposed to repeated flexing. The enclosure will need to have a hole cut to insert the USB plug. The Trinket must be very solidly mounted to the enclosure to sustain the high stress of USB cable insertion. Do not buy buttons that need to be soldered to a board. Buttons should attach to the enclosure.Here are some parameters worth considering when picking an enclosure and buttons:
![how to wire an adafruit trinket how to wire an adafruit trinket](https://cdn-learn.adafruit.com/assets/assets/000/061/238/medium800/3d_printing_Trinket_Question_Block_Sound_Jewelry.png)
I added the references in the hardware list, but these are by no means the only or best options. I just went to my local electronic store and bought some I liked. There is a wide choice of enclosures and buttons to do this project. The SAMD21 inside the new Trinket M0 has USB keyboard and mouse capability in hardware and it has shown to be perfectly reliable. The original Trinket is ATtiny85-based and that chip does not have native USB keyboard capable hardware, so the project uses a bit-banged (i.e. This worked, but not completely reliably, especially behind some USB hubs. I had originally made this project with the older Adafruit Trinket 5V using the Adafruit Trinket USB Keyboard instructions. I like the Trinket M0 because it is really small (and this project only needs a small number of I/Os, so no need for the bigger boards) and it is inexpensive ($8.95). It can be replaced by pretty much any of the other Atmel ATSAMD21-based boards like the Arduino MKR ZERO or the SparkFun SAMD21 Mini Breakout. The key component for this project is the Adafruit Trinket M0. It saves me from having to reach for the keyboard or remembering keyboard shortcuts. This is a very simple, yet useful introductory project to Arduino, USB and buttons.